fds2672 _f085 n-channel ultrafet trench ? mosfet ?20 10 fairchild semiconductor corporation fds2672 _f085 rev. a www.fairchildsemi.com 1 tm february 20 10 mosfet maximum ratings t a = 25c unless otherwise noted thermal characteristics package marking and ordering information symbol parameter ratings units v ds drain to source voltage 200 v v gs gate to source voltage 20 v i d drain current -continuous (note 1a) 3.9 a -pulsed 50 e as single pulse avalanche energy (note 3) 37.5 mj p d power dissipation (note 1a) 2.5 w power dissipation (note 1b) 1.0 t j , t stg operating and storage temperature -55 to 150 c r jc thermal resistance, junction to case (note 1) 25 c/w r ja thermal resistance, junction to ambient (note 1a) 50 r ja thermal resistance, junction to ambient (note 1b) 125 device marking device reel size tape width quantity fds2672 fds2672 _f085 13?? 12mm 2500 units fds2672 _f085 n-channel ultrafet trench ? mosfet 200v, 3.9a, 70m ? features ? max r ds(on) = 70m ? at v gs = 10v, i d = 3.9a ? max r ds(on) = 80m ? at v gs = 6v, i d = 3.5a ? fast switching speed ? high performance trench tec hnology for extremely low r ds(on) ? q ualified to aec q101 general description this single n-channel mo sfet is produced using fairchild semiconductor?s advanced uitrafet trench ? process that has been especially tailored to minimize the on-state resistance and yet maintain superior switching performance. application ? dc-dc conversion pin 1 so-8 4 3 2 1 5 6 7 8 d d d d g s s s ? rohs compliant
fds2672_f085 n-channel ultrafet trench ? mosfet fds2672 _f085 rev. a www.fairchildsemi.com 2 electrical characteristics t j = 25c unless otherwise noted symbol parameter test conditions min typ max units off characteristics bv dss drain to source breakdown voltage i d = 250 a, v gs = 0v 200 v ? bv dss ? t j breakdown voltage temperature coefficient i d = 250 a, referenced to 25 c 206 mv/ c i dss zero gate voltage drain current v ds = 160v, v gs =0v 1 a v ds = 160v, v gs =0v t j = 55 c 10 a i gss gate to source leakage current v gs = 20v 100 na on characteristics v gs(th) gate to source threshold voltage v gs = v ds , i d = 250 a 2 2.9 4 v ? v gs(th) ? t j gate to source threshold voltage temperature coefficient i d = 250 a, referenced to 25 c -11 mv/ c r ds(on) drain to source on resistance v gs = 10v, i d = 3.9a 59 70 m ? v gs = 6v, i d = 3.5a 63 80 v gs = 10v, i d = 3.9a, t j = 125 c 124 148 g fs forward transcondductance v ds = 10v , i d = 3.9a 15 s (note 2) dynamic characteristics c iss input capacitance v ds = 100v, v gs = 0v, f = 1mhz 1905 2535 pf c oss output capacitance 100 135 pf c rss reverse transfer capacitance 30 45 pf r g gate resistance f = 1mhz 0.7 ? switching characteristics t d(on) turn-on delay time v dd = 100v, i d = 3.9a v gs = 10v, r gen = 6 ? 22 35 ns t r rise time 10 20 ns t d(off) turn-off delay time 35 56 ns t f fall time 10 20 ns q g(tot) total gate charge at 10v v dd =100v i d = 3.9a 33 46 nc q gs gate to source gate charge 11 nc q gd gate to drain ?miller?charge 7 nc drain-source diode characteristics v sd source to drain diode voltage v gs = 0v, i s = 3.9a 0.75 1.2 v t rr reverse recovery time i f = 3.9a, di/dt = 100a/ s 67 101 ns q rr reverse recovery charge i f = 3.9a, di/dt = 100a/ s 179 269 nc notes: 1: r ja is the sum of the junction-to-case and case-to- ambient thermal resistance where the case thermal reference is defined as th e solder mounting surface of the drain pins. r jc is guaranteed by design while r ca is determined by the user?s board design. 2: pulse test: pulse width < 300 us, duty cycle < 2.0%. 3: starting t j = 25 c, l = 3mh, i as = 5a, v dd = 100v, v gs = 10v scale 1:1 on letter size paper a) 50c/w (10 sec) 62.5c/w steady state when mounted on a 1in 2 pad of 2 oz copper b) 125c/w when mounted on a minimum pad .
fds2672 _f085 n-channel ultrafet trench ? mosfet fds2672 _f085 rev. a www.fairchildsemi.com 3 typical characteristics t j = 25c unless otherwise noted figure 1. on region characteristics 01234 0 10 20 30 40 50 pulse duration = 80 s duty cycle = 0.5%max v gs = 4.5v v gs = 5v v gs = 6v v gs = 10v i d , drain current (a) v ds , drain to source voltage (v) figure 2. normalized 0 5 10 15 20 25 30 35 40 45 50 0.5 1.0 1.5 2.0 2.5 3.0 v gs = 4.5v v gs = 5v v gs = 6v v gs = 10v i d , drain current(a) normalized drain to source on-resistance pulse duration = 80 s duty cycle = 0.5%max on-resistance vs drain current and gate voltage figure 3. -50 -25 0 25 50 75 100 125 150 0.4 1.0 1.6 2.2 2.8 i d = 3.9a v gs = 10v normalized drain to source on-resistance t j , junction temperature ( o c ) normalized on resistance vs junction temperature figure 4. 3.0 4.5 6.0 7.5 9.0 40 60 80 100 120 140 160 180 pulse duration = 80 s duty cycle = 0.5%max t j = 150 o c t j = 25 o c i d = 3.9a r ds(on) , drain to source on-resistance ( m ? ) v gs , gate to source voltage (v) 10 on-resistance vs gate to source voltage figure 5. transfer characteristics 23456 0 5 10 15 20 25 30 v dd = 10v pulse duration = 80 s duty cycle = 0.5%max t j = - 55 o c t j = 25 o c t j = 150 o c i d , drain current (a) v gs , gate to source voltage (v) figure 6. 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1e-3 0.01 0.1 1 10 100 t j = -55 o c t j = 25 o c t j = 150 o c v gs = 0v i s , reverse drain current (a) v sd , body diode forward voltage (v) source to drain diode forward voltage vs source current
fds2672 _f085 n-channel ultrafet trench ? mosfet fds2672 _f085 rev. a www.fairchildsemi.com 4 figure 7. 0 8 16 24 32 40 0 2 4 6 8 10 v dd = 100v v dd = 50v v gs , gate to source voltage(v) q g , gate charge(nc) v dd = 150v gate charge characteristics figure 8. 0.1 1 10 10 0 10 100 1000 10000 f = 1mhz v gs = 0v capacitance (pf) v ds , drain to source voltage (v) c rss c oss c iss capacitance vs drain to source voltage figure 9. 0.01 0.1 1 10 100 1000 0.1 1 10 t j = 25 o c t j = 125 o c t av , time in avalanche(ms) i as , avalanche current ( a ) unclamped inductive switching capability figure 10. 25 50 75 100 125 150 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 r ja = 50 o c/w v gs = 6v v gs = 10v i d , drain current (a) t a , ambient temperature ( o c ) ambient continuous drain current vs case temperature figure 11. 0.01 0.1 1 10 100 1000 10 -3 10 -2 10 -1 10 0 10 1 10 2 1ms 100us 10ms 100ms 1s dc single pulse t j = max rated t a = 25 o c operation in this area may be limited by r ds(on) limited by package i d , drain current (a) v ds , drain-source voltage (v) forward bias safe operating area figure 12. single 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 2 10 3 1 10 100 1000 v gs = 10v single pulse p ( pk ) , peak transient power (w) t, pulse width (s) 3000 t a = 25 o c i = i 25 for temperatures above 25 o c derate peak 150 t a ? 125 ----------------------- - pulse maximum power dissipation typical characteristics t j = 25c unless otherwise noted
fds2672 _f085 n-channel ultrafet trench ? mosfet fds2672 _f085 rev. a www.fairchildsemi.com 5 figure 13. transient thermal response curve 10 -4 10 -3 10 -2 10 -1 10 0 10 1 10 2 10 3 1e-4 1e-3 0.01 0.1 1 duty cycle-descending order normalized thermal impedance, z ja t, rectangular pulse duration (s) d = 0.5 0.2 0.1 0.05 0.02 0.01 single pulse 2 p dm t 1 t 2 notes: duty factor: d = t 1 /t 2 peak t j = p dm x z ja x r ja + t a typical characteristics t j = 25c unless otherwise noted thermal characterization performed us ing the conditions described in note 1b transient thermal response will change depending on the circuit board design
trademarks the following includes registered and unregistered trademarks and se rvice marks, owned by fairchild semiconductor and/or its gl obal subsidiaries, and is not intended to be an exhaustive list of all such trademarks. *trademarks of system general corporation, used under license by fairchild semiconductor. disclaimer fairchild semiconductor reserves the right to make changes with out further notice to any products herein to improve reliability, function, or design. fairchild does not assume an y liability arising out of the application or use of any product or circuit described herein; neither does it convey an y license under its patent rights, nor the rights of others. these specifications do not expand the terms of fairchild?s worldwide terms and conditions, specifically the warranty therein, which covers these products. life support policy fairchild?s products are not authorized for use as critical components in life support devices or systems without the express written approval of fa irchild semiconductor corporation. as used herein: 1. life support devices or systems ar e devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life su pport device or system, or to affect its safety or effectiveness. product status definitions definition of terms accupower? auto-spm? build it now? coreplus? corepower? crossvolt ? ctl? current transfer logic? deuxpeed ? dual cool? ecospark ? efficentmax? fairchild ? fairchild semiconductor ? fact quiet series? fact ? fast ? fastvcore? fetbench? flashwriter ? * fps? f-pfs? frfet ? global power resource sm green fps? green fps? e-series? g max ? gto? intellimax? isoplanar? megabuck? microcoupler? microfet? micropak? micropak2? millerdrive? motionmax? motion-spm? optihit? optologic ? optoplanar ? ? pdp spm? power-spm? powertrench ? powerxs? programmable active droop? qfet ? qs? quiet series? rapidconfigure? saving our world, 1mw/w/kw at a time? signalwise? smartmax? smart start? spm ? stealth? superfet? supersot?-3 supersot?-6 supersot?-8 supremos? syncfet? sync-lock? ?* the power franchise ? ? tinyboost? tinybuck? tinycalc? tinylogic ? tinyopto? tinypower? tinypwm? tinywire? trifault detect? truecurrent?* serdes? uhc ? ultra frfet? unifet? vcx? visualmax? xs? tm ? tm tm datasheet identification product status definition advance information formative / in design datasheet contains the design specifications for product development. specifications may change in any manner without notice. preliminary first production datasheet contains preliminary data; supplementary data will be published at a later date. fairchild semiconductor reserves the right to make changes at any time without notice to improve design. no identification needed full production datasheet contains final specifications. fair child semiconductor reserves the right to make changes at any time withou t notice to improve the design. obsolete not in production datasheet contains specifications on a product th at is discontinued by fairchild semiconductor. the datasheet is for reference information only. anti-counterfeiting policy fairchild semiconductor corporation?s anti-counterfeiting policy. fairchild?s anti-counterfeiting policy is also stated on our external website, www.fairchildsemi.com, under sales support . counterfeiting of semiconductor parts is a growing problem in the industry. all manufactures of semiconductor products are expe riencing counterfeiting of their parts. customers who inadvertently purchase counterfeit parts experi ence many problems such as loss of brand reputation, substa ndard performance, failed application, and increased cost of production and manufacturing del ays. fairchild is taking strong measures to protect ourselve s and our customers from the proliferation of counterfeit parts. fairchild strongly encourage s customers to purchase fairchild parts either directly from fa irchild or from authorized fairchild distributors who are listed by country on ou r web page cited above. products customers buy either from fairchild directly or fr om authorized fairchild distributors are genuine parts, have full traceability, meet fa irchild?s quality standards for handing and storage and provide access to fairchild?s full range of up-to-date technical and product information. fairchild and our authorized distributors will stand behind all warranties and wi ll appropriately address and warranty issues that may arise. fairchild will not provide any warranty coverage or other assistance for parts bought from unau thorized sources. fairchild is committed to combat this global problem and encourage our customer s to do their part in stopping this practice by buying direct or from authorized distributors. rev. i47 ? fds2672 _f085 rev. a www.fairchildsemi.com 6 fds2672 _f085 n-channel ultrafet trench ? mosfet
|
